Woods Equipment ALITEC VR48A Bedienungsanleitung

OPER ATOR'S MANUALMAN0357VIBRATORY ROLLERVR48A - SN 71111004 & AfterVR66A - SN 144591004 & AfterVR73A - SN 153661104 & AfterVR84A - S

10 Owner ServiceMAN0357 (Rev. 12/10/2007)OWNER SERVICE Before performing any maintenance or serviceon the unit, perform the mandatory safety shut-d

Owner Service 11MAN0357 (Rev. 12/10/2007) Figure 24. Remove the shaft nut (13, using part number1023106 socket), the shaft washer, and thetongued wash

12 Owner ServiceMAN0357 (Rev. 12/10/2007)BEARING INSTALLATION1. Apply a small amount of lubrication (oil or grease)to the outer bearing housing.2. Ass

Owner Service 13MAN0357 (Rev. 12/10/2007) Figure 11. Remove Spring Retaining Ring4. Firmly grasp the top of the shaft and pull assemblyfrom motor. 5.

14 Owner ServiceMAN0357 (Rev. 12/10/2007)NOTES

Troubleshooting / Dealer Service 15MAN0357 (Rev. 12/10/2007)TROUBLESHOOTINGDEALER SERVICEAlthough the Alitec attachment is supplied fully assem-bled,

16 PartsMAN0357 (Rev.12/10/2007)VIBRATORY ROLLER GENERAL ASSEMBLYREF PART QTY DESCRIPTION1 105382 1 Chassis weldment, VR48A1 105373 1 Chassis weldment

Parts 17MAN0357 (Rev. 12/10/2007)VIBRATORY ROLLER GENERAL ASSEMBLYREF PART QTY DESCRIPTION4 101711 1 Drum weldment, 48" VRA Smooth4 101434 1 Drum

18 PartsMAN0357 (Rev.12/10/2007)OPTIONAL FLOW CONTROL KITSREF PART QTY DESCRIPTION1 1007693 1 Priority flow 17 gpm (used in kit 1012103)1 1007694 1 Pr

Appendix 19Bolt Torque & Size Charts (Rev. 3/28/2007)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or t

2 IntroductionGen’l (Rev. 2/19/2008)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read ma

20 AppendixBolt Torque & Size Charts (Rev. 3/28/2007)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for

F-3079 (Rev. 5/15/2008)WARRANTY(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)Please Enter Information Belo

F-8494 (Rev. 6/23/2005)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxw

Introduction 3MAN0357 (Rev. 12/10/2007)TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 IntroductionMAN0357 (Rev. 1/5/2007)SPECIFICATIONSVR48A VR66A VR73A VR84ADrum Width 48 inches (129 cm) 66 inches (168 cm) 73 inches (186 cm) 84 inche

Safety 5Alitec Vibratory Roller Safety Rules (Rev. 1/5/2007)INSTALLATION Hydraulics must be connected as instructed inthis manual. Do not substitute

6 SafetyAlitec Vibratory Roller Safety Rules (Rev. 1/5/2007)(Safety Rules continued from previous page) Always wear relatively tight and belted cloth

Safety 7Alitec Vibratory Roller Safety Rules (Rev. 1/5/2007)MAINTENANCE Before leaving operator's seat, lower lift armsand put attachment on the

8 SafetyMAN0357 (Rev. 12/10/2007)MODEL NO. SERIAL NO.Woods Equipment CompanyOregon, Illinois, U.S.A.30 - Serial Number PlateTO AVOID SERIOUS INJURY OR

Operation 9MAN0357 (Rev. 12/10/2007)OPERATIONThe Vibratory Roller is a hydraulically powered attach-ment intended to compact soil, stone, or fill mate